added arduino, modified build

arduino/libraries/Ethernet/examples/WebClient/WebClient.ino

@@ -0,0 +1,137 @@
+/*
+  Web client
+
+ This sketch connects to a website (http://www.google.com)
+ using an Arduino Wiznet Ethernet shield.
+
+ Circuit:
+ * Ethernet shield attached to pins 10, 11, 12, 13
+
+ created 18 Dec 2009
+ by David A. Mellis
+ modified 9 Apr 2012
+ by Tom Igoe, based on work by Adrian McEwen
+
+ */
+
+#include <SPI.h>
+#include <Ethernet.h>
+
+// Enter a MAC address for your controller below.
+// Newer Ethernet shields have a MAC address printed on a sticker on the shield
+byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };
+
+// if you don't want to use DNS (and reduce your sketch size)
+// use the numeric IP instead of the name for the server:
+//IPAddress server(74,125,232,128);  // numeric IP for Google (no DNS)
+char server[] = "www.google.com";    // name address for Google (using DNS)
+
+// Set the static IP address to use if the DHCP fails to assign
+IPAddress ip(192, 168, 0, 177);
+IPAddress myDns(192, 168, 0, 1);
+
+// Initialize the Ethernet client library
+// with the IP address and port of the server
+// that you want to connect to (port 80 is default for HTTP):
+EthernetClient client;
+
+// Variables to measure the speed
+unsigned long beginMicros, endMicros;
+unsigned long byteCount = 0;
+bool printWebData = true;  // set to false for better speed measurement
+
+void setup() {
+  // You can use Ethernet.init(pin) to configure the CS pin
+  //Ethernet.init(10);  // Most Arduino shields
+  //Ethernet.init(5);   // MKR ETH shield
+  //Ethernet.init(0);   // Teensy 2.0
+  //Ethernet.init(20);  // Teensy++ 2.0
+  //Ethernet.init(15);  // ESP8266 with Adafruit Featherwing Ethernet
+  //Ethernet.init(33);  // ESP32 with Adafruit Featherwing Ethernet
+
+  // Open serial communications and wait for port to open:
+  Serial.begin(9600);
+  while (!Serial) {
+    ; // wait for serial port to connect. Needed for native USB port only
+  }
+
+  // start the Ethernet connection:
+  Serial.println("Initialize Ethernet with DHCP:");
+  if (Ethernet.begin(mac) == 0) {
+    Serial.println("Failed to configure Ethernet using DHCP");
+    // Check for Ethernet hardware present
+    if (Ethernet.hardwareStatus() == EthernetNoHardware) {
+      Serial.println("Ethernet shield was not found.  Sorry, can't run without hardware. :(");
+      while (true) {
+        delay(1); // do nothing, no point running without Ethernet hardware
+      }
+    }
+    if (Ethernet.linkStatus() == LinkOFF) {
+      Serial.println("Ethernet cable is not connected.");
+    }
+    // try to congifure using IP address instead of DHCP:
+    Ethernet.begin(mac, ip, myDns);
+  } else {
+    Serial.print("  DHCP assigned IP ");
+    Serial.println(Ethernet.localIP());
+  }
+  // give the Ethernet shield a second to initialize:
+  delay(1000);
+  Serial.print("connecting to ");
+  Serial.print(server);
+  Serial.println("...");
+
+  // if you get a connection, report back via serial:
+  if (client.connect(server, 80)) {
+    Serial.print("connected to ");
+    Serial.println(client.remoteIP());
+    // Make a HTTP request:
+    client.println("GET /search?q=arduino HTTP/1.1");
+    client.println("Host: www.google.com");
+    client.println("Connection: close");
+    client.println();
+  } else {
+    // if you didn't get a connection to the server:
+    Serial.println("connection failed");
+  }
+  beginMicros = micros();
+}
+
+void loop() {
+  // if there are incoming bytes available
+  // from the server, read them and print them:
+  int len = client.available();
+  if (len > 0) {
+    byte buffer[80];
+    if (len > 80) len = 80;
+    client.read(buffer, len);
+    if (printWebData) {
+      Serial.write(buffer, len); // show in the serial monitor (slows some boards)
+    }
+    byteCount = byteCount + len;
+  }
+
+  // if the server's disconnected, stop the client:
+  if (!client.connected()) {
+    endMicros = micros();
+    Serial.println();
+    Serial.println("disconnecting.");
+    client.stop();
+    Serial.print("Received ");
+    Serial.print(byteCount);
+    Serial.print(" bytes in ");
+    float seconds = (float)(endMicros - beginMicros) / 1000000.0;
+    Serial.print(seconds, 4);
+    float rate = (float)byteCount / seconds / 1000.0;
+    Serial.print(", rate = ");
+    Serial.print(rate);
+    Serial.print(" kbytes/second");
+    Serial.println();
+
+    // do nothing forevermore:
+    while (true) {
+      delay(1);
+    }
+  }
+}
+