added arduino, modified build

arduino/libraries/Firmata/examples/StandardFirmataEthernet/ethernetConfig.h

@@ -0,0 +1,94 @@
+/*==============================================================================
+ * NETWORK CONFIGURATION
+ *
+ * You must configure your particular hardware. Follow the steps below.
+ *
+ * By default, StandardFirmataEthernet is configured as a TCP client.
+ * To configure as a TCP server, see STEP 2
+ *============================================================================*/
+
+// STEP 1 [REQUIRED]
+// Uncomment / comment the appropriate set of includes for your hardware (OPTION A or B)
+// Option A is enabled by default.
+
+/*
+ * OPTION A: Configure for Arduino Ethernet board or Arduino Ethernet shield (or clone)
+ *
+ * To configure StandardFirmataEthernet to use the original WIZ5100-based
+ * ethernet shield or Arduino Ethernet uncomment the WIZ5100_ETHERNET define below
+ */
+#define WIZ5100_ETHERNET
+
+#ifdef WIZ5100_ETHERNET
+#include <SPI.h>
+#include <Ethernet.h>
+EthernetClient client;
+#endif
+
+/*
+ * OPTION B: Configure for Arduin Yun
+ *
+ * The Ethernet port on the Arduino Yun board can be used with Firmata in this configuration.
+ *
+ * To execute StandardFirmataEthernet on Yun uncomment the YUN_ETHERNET define below and make
+ * sure the WIZ5100_ETHERNET define (above) is commented out.
+ *
+ * On Yun there's no need to configure local_ip and mac address as this is automatically
+ * configured on the linux-side of Yun.
+ *
+ * Note that it may take several seconds to establish a connection with the Yun.
+ */
+//#define YUN_ETHERNET
+
+#ifdef YUN_ETHERNET
+#include <Bridge.h>
+#include <YunClient.h>
+YunClient client;
+#endif
+
+// STEP 2 [REQUIRED for all boards and shields]
+// TCP Client configuration:
+// To configure your board as a TCP client, set the IP address of the server you want to connect to.
+// TCP Server configuration:
+// To configure your board as a TCP server, comment out the following line and also ensure that
+// remote_host is also commented out.
+#define remote_ip IPAddress(10, 0, 0, 3)
+// *** REMOTE HOST IS NOT YET WORKING ***
+// replace with hostname of server you want to connect to, comment out if using 'remote_ip'
+// #define remote_host "server.local"
+
+// STEP 3 [REQUIRED]
+// Replace with the port that your client or server is listening on.
+#define network_port 3030
+
+// STEP 4 [REQUIRED unless using DHCP]
+// Replace with your board or ethernet shield's IP address
+// Comment out if you want to use DHCP
+#define local_ip IPAddress(10, 0, 0, 15)
+
+// STEP 5 [REQUIRED]
+// replace with ethernet shield mac. Must be unique for your network
+const byte mac[] = {0x90, 0xA2, 0xDA, 0x00, 0x53, 0xE5};
+
+/*==============================================================================
+ * CONFIGURATION ERROR CHECK (don't change anything here)
+ *============================================================================*/
+
+#if !defined WIZ5100_ETHERNET && !defined YUN_ETHERNET
+#error "you must define either WIZ5100_ETHERNET or YUN_ETHERNET in ethernetConfig.h"
+#endif
+
+#if defined remote_ip && defined remote_host
+#error "cannot define both remote_ip and remote_host at the same time in ethernetConfig.h"
+#endif
+
+/*==============================================================================
+ * PIN IGNORE MACROS (don't change anything here)
+ *============================================================================*/
+
+#if defined(WIZ5100_ETHERNET)
+
+// ignore SPI pins, pin 10 (Ethernet SS) and pin 4 (SS for SD-Card on Ethernet shield)
+#define IS_IGNORE_PIN(p) ((IS_PIN_SPI(p) || (p) == 4) || (p) == 10)
+
+#endif